How to save $650 on a Pottery Barn knock-off bench!

We all want to save $650, right?  What if I said you can save $650 and have a beautiful wood storage bench?  That’s a no brainer! Who wouldn’t!?

My friend Shara over at Woodshop Diaries found this bench in the Pottery Barn catalog:

Screen Shot 2017-04-13 at 4.43.28 PM

And guess what, it’s $700. SEVEN HUNDRED DOLLARS.

Shara joined in the #PlywoodPretty challenge and built this bench and inspired me to do the same (only I modified mine a little bit)!

Since I wanted to build this bench in a day and I didn’t want to have Bryn’s help for most of it, I decided to take some shortcuts with this project.  So, on top of the how-to, i’m going to share my shortcuts!

DSC_0828

Isn’t this just a beautiful entryway storage bench? It’s almost EXACTLY the same as the Pottery Barn bench.

And here’s the best part.  I spent $50. FIFTY DOLLARS. That’s it.

I know you want to build your own, so let’s get started.

Materials:
1 ¾” sheet of birch plywood
¼ sheet of ¼” plywood
1 1/4″ Kreg Pocket Screws


Tools:
Table saw
Miter Saw
Jig Saw
Kreg Pocket Hole Jig System
Router
Drill
Sander (or sandpaper)

STEP ONE
Cut the plywood into pieces for the bench.  Shara made the diagram below and I thought it was extremely helpful!

Screen Shot 2017-04-13 at 4.57.19 PM

In order to cut these to size, you can use a table saw or circular saw.

** Shortcut** If you don’t have these tools or want to make it a tad easier for yourself, you can have the workers at Home Depot cut your plywood for you!  I picked out my plywood, then told the nice gentlemen the exact measurements I needed and within 10 minutes it was all cut to size. And for another bonus, it will fit in your car!

STEP TWO
Make the sides of your bench.

After cutting the 26 x 36 piece of plywood, rip it in half using the table saw.  Be sure your pieces are EXACTLY the same.

IMG_4442

Mark 8 inches from the top, as this is where the bench seat will attach. You don’t want to cut your design any lower than that.

Draw any curved shape you want.  I tried to make mine look exactly like the curve on the Pottery Barn website.

IMG_4444

Draw a design for the legs on the bottom.  Be sure not to cut higher than 3 ½ inches, as this is where the bottom of the drawers will be!

Use a jig saw to cut out your design.  Depending on how steep your curves are, this can be a little challenging. Take your time!

IMG_4446

**Shortcut** Once I cut one side with the jig saw, I was able to use the router to make the other piece look exactly like the first one! This saved me a lot of time and concentration.

IMG_4447

IMG_4452

STEP THREE
Attach the bench seat.

Run the 33 x 36’’ piece through the table saw to get two 33 x 18” pieces.

Drill pocket holes in each end and attach them to the side panels.

IMG_4451

STEP FOUR
Add the backrest.

Use the 7 ½’’ strip (from the diagram) to cut your backrest.  Depending on the size of your curve, the height may vary.  Just be sure the backrest does not go higher than your curve.

IMG_4457

IMG_4461

Once cut to size, add pocket holes and screw into place.

STEP FIVE
Cut the drawer divider to size and attach to bench.

IMG_4460

Use the 13’ wide strip (from the diagram) to cut a divider to size.  Depending on your actual bench measurements this may vary.  Just be sure it’s snug and perfectly centered.

IMG_4458

STEP SIX
Add the drawers.

You can use drawer slides from a hardware store, however I didn’t want to take the time for that. (Remember, I said I wanted this all done in one day!)

Instead, I decided to build the drawers to fit exactly in the spaces.

You’ll need to cut two side pieces and a back piece to the exact size you want them (the white part of the diagram).  I made the drawer just a little bit shorter than the actual bench (so it doesn’t poke out the other side).  Once they were cut to size, I made a small groove on the bottom of the pieces for a ¼’’ plywood board to slide into.

IMG_4466

Add pocket holes and screw them together.

IMG_4462

You’ll want to make the face of the drawer the exact size of the opening (well, maybe a tad bit smaller so it will slide in and out).  So, once that was cut to size I was able to attach it to the drawer.

IMG_4468

To be sure the drawers slide in and out easily, I used some wax polish that I got from Linn’s shop over at Darbin Orvar.  It’s great stuff, I highly recommend it! (I put this on at the very end.)

DSC_0796

I bought these handles from Lowes, spray painted them black and attached them to the middle of the drawer fronts (again, I attached them at the very end).

DSC_0791

STEP SEVEN
Stain and finish the bench.

I decided to leave the plywood edges showing, because I like the more farmhouse/rustic look.

Once you stain the bench, finish it with a polycrylic and you’re done!

IMG_4473

DSC_0811

It’s just lovely and the drawers are huge! They are perfect for hats, gloves, dog leashes, towels, and whatever else you may want to hide (instead of having all of these things laying on your entryway floor)!

If you ask me, I think this is better than the $700 Pottery Barn version.  It’s actual plywood and it was homemade!

DSC_0809

DSC_0836 (1)

DSC_0814

And if you want to see a video on how to build this, check out Shara’s page (she posted her first ever build video)!

While you’re here, go ahead and PIN this for later!

You may also like:

Morning wedding_PIN   Floating Shelves_PIN

gallery wall pin   DIY wood planter

 

4 thoughts on “How to save $650 on a Pottery Barn knock-off bench!

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s